In NZ, tiles are an incredibly popular flooring solution. But have you ever noticed how challenging it can be to seamlessly transition between tiles and another surface, like wood? It can be especially tricky if the two surfaces are at differentheights.
Transition strips are narrow strips of metal that bridge the gap between the two surfaces and create a smooth transition. They come in various styles and colours, so you can pick one that matches your tile and woodperfectly.
How To Transition Between Wood AndTiles
Installing a transition strip is straightforward. Here's a run-down of theprocess:
- You'll need to cut the strip to fit the width of the gap in yourfloor.
- Trim the bottom of the strip so it's level with the height of yourtile.
- Once the strip is the right size, attach it to the subfloor with a nail gun or hammer and nails. Make sure you nail it in place securely because it needs to support the weight of the tile.
Once the transition strip is in place, you can start tiling like usual. Just ensure the tile's edge is flush with the edge of the transition strip. You can use a tile saw or a wet tile cutter to make clean, precise cuts. And that's it! You're all set with your new transitionstrip.
How to Finish Tile WithEdging
Edging in tiles refers to the process of creating a finished edge on a tiled surface. This is usually done by using tile trim, which is a strip of material that is placed along the edge of the tiles to give the surface a clean, finished look. Tile edging can also be used to protect the edges of the tiles from chipping or cracking. It is an important step in tile installation, as it helps to create a professional-looking finish and ensures that the tiling will last for many years tocome.
One way to finish tile edges is by using edging strips. Edging strips are thin strips of material, such as metal, plastic, or wood, that create a smooth, finished edge around the perimeter of a tiled surface. These strips can cover the tiles' raw edges, creating a seamless transition between the tiles and the surroundingsurfaces.
Here's the process of using edgingstrips:
- First, measure the perimeter of the tiled surface and cut the edging strips to the appropriate length. Be sure to leave a small gap between the ends of the edging strips to allow for the expansion and contraction of thetiles.
- Next, carefully position the edging strips along the edges of the tiled surface, using a spirit level to ensure they are level andstraight.
- Once the edging strips are in place, secure them to the surface using a hammer and nails or tile adhesive. Be sure to use enough nails or adhesive to ensure the strips are securely attached, as they will support the tiles'weight.
- Once securely in place, use a tile saw or angle grinder to carefully trim the tiles to fit along the edge of the edging strips to create a seamless transition between the tiles and the edgingstrips.
- Finally, use a grout float to apply grout along the edges of the tiles, ensuring that any gaps between the tiles and the edging strips arefilled.
- Next, use a damp sponge to remove excess grout and smooth the grout lines. Once the grout has dried, your tile edges will be finished and ready to beenjoyed.
How to Finish Tile Edges WithSilicon
Before diving into the process, let’s understand what silicon is and why it’s a good choice for finishing tile edges. Silicon is a flexible, water-resistant sealant commonly used in various applications, including around windows and doors and bathrooms and kitchens. It is available in multiple colours to match your tiles and can be easily applied using a silicongun.
Before applying the silicon, you need to ensure that the tile edges are clean and free of debris. Use a damp cloth to wipe down the edges, then allow them to dry completely. If the tiles are uneven or there are gaps between them, you can use a grout float to smooth them out and create a flatsurface.
Once the tile edges are clean and smooth, it's time to apply the silicon. Here are the steps for finishing tile edges withsilicon:
- Start by loading the silicon into a silicon gun. Then, cut the tip of the silicon tube at a 45-degree angle to create a fine line ofsilicon.
- Hold the silicon gun at a 45-degree angle and slowly run it along the edge of thetile.
- Use a steady, even pressure when applying the silicon, and make sure to fill in any gaps or spaces between thetiles.
- Starting at one end of the tile edge, apply the silicon by pressing the tube and moving it steadily along theedge.
Try to keep the silicon bead as smooth and even as possible. If necessary, use a silicon smoothing tool or your finger to smooth out any bumps orgaps.
Once the silicon has been applied, allow it to dry according to the manufacturer's instructions. Depending on the type of silicon and the conditions in your home, this can take anywhere from a few hours to a fullday.
After the silicon has dried, it's time to clean up any excess silicon that may have squeezed out or dripped down the edge of the tile. Use a utility knife or scraper to carefully remove any excess silicon. Again, be careful not to damage the silicon bead or the tileitself.
Once the silicon has been applied, allow it to dry according to the manufacturer’s instructions. This can take anywhere from a few hours to a full day, depending on the type of silicon and the conditions in yourhome.
After the silicon has dried, it’s time to clean up any excess silicon that may have squeezed out or dripped down the edge of the tile. Use a utility knife or scraper to remove any excess silicon carefully. Again, be careful not to damage the silicon bead or the tileitself.
Once the excess silicon has been removed, the tile edge should be smooth and professionally finished. You can then apply any grout or other finishing touches asdesired.
Overall, finishing tile edges with silicon is a relatively simple process that can give your tile work a clean, professional-looking finish. In addition, you can easily complete this task independently with the right tools andpatience.
How To Mitre An Internal And ExternalCorner
What isMitering?
Mitring is a technique used in tile installation. In this technique, the edges of the tiles are cut at an angle to create a seamless, continuous look around corners. The tiles are cut at a 45-degree angle, which allows them to fit together snugly and create a clean, finishedlook.
Mitring can be used on internal and external corners and is a popular choice for tiling projects because it provides a professional-looking finish without needing complicated tile trim or specialtools.
You will need the following tools andmaterials:
- Wet saw or tilecutter
- Measuringtape
- Pencil orchalk
- A setsquare
- A mitrebox
- A tilenipper
How To Mitre An InternalCorner
So how do you mitre a tile? First, let's start with internal corners. The most common method for tiling an internal corner is to use a 45-degree angle, also known as a mitre cut. This involves cutting the tiles at a 45-degree angle on both sides of the corner, creating a seamless joint between the twotiles.
Tobegin:
- Measure the length and width of the corner to determine the size of yourtile.
- Using a pencil and a straight edge, mark the 45-degree angle on the tile. Measure twice and mark once to ensure a precisecut.
- Once the angle has been marked, carefully cut along the marked line with a wet saw. Wet saws are power saws that use a blade with diamond-encrusted teeth to make precise cuts in ceramic or porcelain tiles. They are ideal for making straight and angled cuts and can be purchased at most home improvementstores.
Once cut, it's time to install the tiles in thecorner.
- Using a notched trowel, apply a thin layer of tile adhesive to thecorner.
- Carefully place the first tile in the corner, pressing it firmly into theadhesive.
- Repeat this process for the second time and line up the 45-degree angles to create a seamless joint. Again, use a level to ensure the tiles are properly aligned and adjust asneeded.
How To Mitre An ExternalCorner
One of the most common ways to deal with tile edges is to create a mitred joint, where two tiles are cut at an angle to fit neatly in an external corner. Here's how to doit:
Measure and mark the tiles: To create a perfect mitred joint, you'll need to measure and mark the tiles accurately. Use a tape measure to determine the width of the tiles that will be meeting at the corner, and use a pencil to mark a line across the tile where it will becut.
Use a tile cutter or wet saw: Once you've marked the tiles, you'll need to cut them to the appropriate angle using a tile cutter or wet saw. A tile cutter is a hand-held tool that uses a scoring wheel to create a line in the tile that can be easily snapped along the mark. On the other hand, a wet saw uses a diamond blade to make precise cuts in thetile.
Dry-fit the tiles: Before applying any adhesive, it's a good idea to dry-fit the tiles to make sure they fit together perfectly. Place the tiles in the corner, ensuring the cut edges meet at the desired angle. Adjust the tiles as needed until they fit togethersnugly.
Apply adhesive and grout: Once you're satisfied with the fit of the tiles, you can begin applying adhesive to the back of the tiles. First, use a notched trowel to spread the adhesive evenly, making sure to cover the entire surface of the tile. Then, carefully place the tiles in the corner, pressing them firmly intoplace.
Find Your New TilesToday
Jacobsen Flooring offers an extensive range of residential flooring solutions, making it easy to find the perfect tile for your space. Explore the full collection online today and create the perfect tile edges in yourhome.
